iMod X500 PlusIndustrial computer NPE X500 Plus with iMod software, Telemetry Module, ARM11, 700MHz, 512 MB Ram, 4096 MB Flash, Linux 3.6, RTC, 240 byte SRAM, Watch Dog Timer, 1 x RJ-45 10/100 Mbps, 3 x RS-232 / 2 x RS-485, 4 x DI, 4 x DO, 2 x AI, 1 x 1-Wire, 1 x USB 2.0, 1 x SIM CARD slot, LTE, M-Bus, Wi-Fi, Bluetooth, GPS, Zigbee, embedded computer, serial server, IoT, iMod, GPIO, Modbus, MQTT, SNMP
iMod X500 PLUS - modern, ready-to-use platform for automation systems.
What is iMod X500 PLUS?
Proper selection of hardware resources and ready to use software packages enable you to adjust the functionalities of the device according to the requirements of your installation.
The iMod platform combines ease of use characteristic of simple devices with possibilities of an embedded computer.
With ready to use solutions, you will significantly reduce the time necessary to launch your installation.
Due to constant development of applications and the possibility of remote update, you can update software and constantly increase the scope of functions of your device.
iModCloud - dedicated cloud service
iModCloud - a cloud service - allows you to visualize and control parameters of any number of devices via a web browser.
With iModCloud you can control all your facilities via any mobile device, register data and share selected information with other users.
See the basic functionalities of the iMod platform:
One of the main advantages of the iMod platform is its ease of use and variety of available functionalities. Due to the available SDK, the platform can be extended with new dedicated functionalities.
The iMod platform guarantees a quick start and full use of the NPE computer, without the need to write complicated software. It is a fully configurable system, that represents the typical C-L-V usage.
Functionality of a protocol and interface converter (Convert) collecting data from input interfaces (e.g. Ethernet or USB), converting and transferring to output interfaces, ZigBee, GPRS or to external modules. All the protocols supported by the iMod computer (M-Bus, Modbus, 1-Wire, TCP/IP, SNMP) can be used both as a source and target of conversion.
Functionality of a data logger (Log)The iMod industrial computer can read data from connected devices at high speed. The data can be saved on the device (to internal Flash memory or SD/MMC card) or can be transferred asynchronously to external data bases (PostgreSQL or SQLite). All the archived data can be shared via external or internal systems (e.g. SCADA).
Functionality of access via Websites (Visualize) Graphic Visualization, via Web browser, in order to read and control processed data and alarm statuses - you can use a built-in Apache server and an innovative Web platform - NX Dynamics.
iMod X500 PLUS can perform the following functions:
iMod X500 PLUS telemetry module offers you huge opportunities of registering and data access, using built-in input/output interfaces and communication channels, such as:
Protocol and Interface Converter:
Due to flexible configuration, the device can operate as a protocol and interface converter:
In addition, due to the possibilities of the Linux operating system, each user can create their own protocols with the use of the available SDK.
Embedded Web Server Your can visualize and control parameters via a web browser directly from the device The web-based graphical user interface - NX Dynamics - simplifies the control of the device and allows you to create advanced visualizations.
The design of the iMod X500 PLUS allows for trouble-free operation in industrial conditions. It has a fanless case and is characterised by high resistance to external conditions and high reliability. The Linux system provides stable operation of the device.
iMod X500 PLUS is a multichannel telemetry module, providing constant uninterrupted access to data. It enables you to save the results of measurements and parameter values of connected devices - data can be saved to internal memory or to an SD/MMC card. You can also save data to internal and external databases.
iMod X500 PLUS can generate alarm signals and provide information on current parameter values. Built-in GPRS/3G modem enables wireless communication.
iMod X500 PLUS can operate as a typical PLC. The telemetry module can be programmed in ladder logic, which is easy to configure and allows for a quick start of an installation..
Due to the Linux operating system - iMod X500 PLUS is a stable central unit of an automation system.
Industrial modem and GPRS/3G router:
With a built-in GSM modem, iMod X500 PLUS offers advanced functions and can be configured as an industrial modem and a router operating in GPRS, EDGE network as well as in 3G mobile network. You can easily get a backup connection mode and define routing.
You can build a VPN with iMod X500 PLUS. You can access other devices with one telemetry module with a defined public IP. The VPN guarantees high security of data transmission.
3G technology provides higher speed and lower latency at packet data transmission.
I/O Expansion Module:
Due to digital I/O and analog inputs, iMod X500 PLUS can successfully replace expansion modules.
The iMod device allows:
GSM / GPRS / EDGE /3G Notify Module:
With a built-in GSM modem, the iMod X500 PLUS industrial computer can operate as a notify module: it can send alerts when defined parameter values are exceeded (e.g. temperature, humidity). You can easily and quickly configure the content of a message which is send instantly when the value is exceeded. System supervisor will immediately receive SMS or e-mail notification.
A GPS receiver allows to use the satellite navigation system. The system is widely used in vehicle monitoring (e.g. transport, railway industry or municipal communication). It allows to synchronize time in extensive industrial networks. It is also used to set a route for industrial machines.
What you should know about our device
Hardware and software features of the device:
Adaptation for Industrial Conditions:
Three ways to access the resources of the device:
There are three ways to access the hardware and software resources of the device:
NX Dynamics – Web-based Graphical User Interface. Enables you to build your own modules (e.g. for process visualization).
HMI– due to a range of communication interfaces and built-in protocols, you can connect any HMI panel and manage the installation locally.
WWW – the device has a built-in web server, data base and PHP language support. You can easily create and share a dedicated website with view and control functions of selected parameters of the device.
Protocols and SDK:
iMod operates on the NPE hardware platform with Linux operating system. Linux provides a wide range of programming tools, e.g. C, C++, Java support, tools for data bases support, SSH, SSL and VPN.
The is a variety of communication protocols implemented in the iMod platform (these allow for communication with the most popular automation devices), such as:
There is also a possibility to add additional protocols. We have prepared an SDK (Software Development Kit) - a set of tools for adding new functionalities and mechanisms in “plug-in” system. It enables the advanced system integrators to adjust the platform to their solutions.
Internal Architecture of the device:
The iMod X500 PLUS Platform was designed to cooperate with all the modern automation systems communications and telecommunications, at the same time providing clear and flexible configuration. This is why there are 3 types of communication channels defined:
Source Channel – a channel for cyclic retrieving the values of defined parameters (e.g. Modbus Master polls other devices)
Access Channel – this channel allows access to iMod data (e.g. Modbus Slave shares data with SCADA software)
Message Channel– Event-triggered communication allows for notification e.g. by SMS, email or Modbus Push
Apart from the channels defining the communication structure of the iMod device, there are other configuration elements, such as: parameters, events, messages.
Message template send to predefined recipients. You can also insert MACROS in the messages, which will be dynamically filled when the message is sent.
After defining sources, ways of access and message channels you need to define parameters.
Each parameter has an alphanumeric, unique ID for creating an internal array of parameters. Apart from the ID, you need to provide the information on the defined source-channel, where the parameter will retrieve its value. You can also add a proper access-channel, if you want to share the values.
You can easily view and share data. You can also add a mechanism for event-triggered actions, e.g. sending email. You assign message channels and predefined message templates.
Industrial computer NPE 9500 with iMod Software, ARM11, 700MHz, 512 MB Ram, 4096...
Industrial computer NPE X500 Plus, ARM11, 700MHz, 512 MB Ram, 4096 MB Flash, Lin...
Industrial computer NPE X500 with iMod Software, Telemetry Module, ARM11, 700MHz...
NPE X500 - Industrial IoT Gateway Computer, Quad-core Cortex A53 1.2 GHz or ARM1...
Industrial Computer NPE X1000 with iMod software, Telemetry Module, Cortex A8 80...
Industrial computer NPE X1000, Cortex A53 1.2GHz, Linux, 4x DI, 4x DO, up to 24x...
Industrial computer NPE M500 with iMod software, Telemetry Module, ARM Cortex-A5...
Fanless Embedded System, Intel Atom 1.1GHz, 2x RS232/422/485, 1x 100base-tx, 1x ...
Fanless Embedded System, Intel Atom 1.33GHz, 2x RS232/422/485, 1x 100base-tx, 1x...
Fanless Embedded System, Intel Atom 1.1GHz, 2x CAN, 2x RS232/422/485, 1x 100Base...
Industrial computer NPE M500, ARM Cortex-A53, quad-core 1.2GHz (64bit), 1GB Ram,...
Industrial computer NPE M9500 with iMod software, Telemetry Module, ARM Cortex-A...